Operating, Servicing, and maintaining a passenger vehicle or off-road vehicle can expose you to chemicals including engine exhaust, carbon monoxide, phthalates, and lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
To minimize exposure, avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle in a well-ventilated area and wear gloves or wash your hands frequently when servicing your vehicle. For more information go to www. For videos and more information about a safe riding experience with your vehicle, scan this QR code with your smart phone or click on it in a web browser. Unless noted, trademarks are the property of Polaris Industries Inc.
Remember that all warranty claims for boilers still covered by it should be made at www. Shipping costs are not included in the warranty coverage. Troubleshooting Manual Attention! General Information Laars Boilers are designed for indoor installations primary. Venting All Laars commercial and domestic use boilers require special venting system.
Table above shows for proper diameter vs. Maintenance an annual service For economical, functionality and environmental purposes your appliance you should be serviced annually.
Service specialist will verify, correct, replace following things: lubricate the system water-circulating pump clean the stainer if fitted verify the venting system for obstruction or leakage clean the screens in the vent terminal and combustion air terminal when used clean the appliance area verify low water cutoffs, flush float-type low water cutoffs verify and clean he condensate collection and the float switch verify that the condensate is being neutralized properly verify the flue passages, and clean with a brush or vacuum if necessary verify the vent system and air intake system, and ensure that all joints are sealed properly.
Fault codes The two tables below includes a listing of the faults that might be generated by the controller, and displayed on the operator interface. Table 1. In instances when the fault repeats, replace module. Internal sub-system fault.
Review alert messages for possible trends. Correct possible problems. Verify main valve wiring and operation — correct any errors. Verify the fuel supply. Verify fuel pressure and repeat turn down tests. Verify ignition transformer electrode, flame detector, flame detector siting or flame rod position. When the fault persists, replace the module. Verify wiring and correct any potential wiring errors.
Change the VFD. If the fault persists, replace the module. Verify and correct terminal wiring of the main valve. Reset the module. If problem continue, module should be replaced. Verify terminal ignition wiring and fix where needed. Verify wiring and correct any errors.
Inspect the Block Intake Switch to make sure it is working correctly. During Standby and Purge, measure the voltage across the switch. Supply voltage should be present. If not, the Block Intake Switch is defective and needs replacing.
If the fault persists, replace the relay module. Verify parameters and iff needed manually reset module. If fault consists, electrical grounding need to be checked. If fault continue, replace module. Fault code. Error message. Internal fault- hardware fault. Reset module. Internal fault- key feedback safety relay fault.
Internal fault- power DC output unstable. Internal fault- clock processor invalid. Internal fault- safety relay drive error. Internal fault- no zero crossing. Internal fault- bias flame out of range. Internal fault- short relay safety drive cap. Internal fault- overflow and flame ripple. Internal fault- sample mismatch flame number. Internal fault- out of range flame bias. Internal fault- since heating cycle starts bias changed. Internal fault- stuck low or high spark voltage. Internal fault- during flame sensing time spark voltage changed too much.
Internal fault- flame static ripple. Internal fault- shorted flame rod to ground detected. Internal fault- bias flame is not settable in range. Internal fault- shorted to adjacent pin flame bias. Powers on, transistor tubes are all glowing, display works partially,. Selling as-is. From the liquidation of a established chiropractic practice. Condition is Used. Email Poster Message. InVivo Water Jacket Option.
High Field Strength Option. Low Frequency Option. External Coil Option. MagneTherm Accessories. We have a range of accessories to complement your magneTherm System.
MagneTherm Consumables. We have a range of consumables to complement your magneTherm System. Conferences Request a quotation. We use cookies to ensure that we give you the best experience on our website.
0コメント