Sony psp umd tools

The Artist. CGShape Joined in Likes 5. So, I can fairly say that I have almost 28 years of experience. Artist's Website: www.

Contact Artist. Royalty Free Editorial Use Only. The intellectual property depicted in this model, including the brand Sony, is not affiliated with or endorsed by the original rights holders. This model may not be used in a commercial, promotional, advertising or merchandising manner of any kind unless legal clearances are obtained from the third party intellectual property owners.

Included Formats. Favorites: 0 Likes: 0 Views: User Ratings. Not Rated Yet. Also includes high resolution textures. Perfect for extreme close-ups. All materials and textures are included and mapped in every format. The 3ds max zip file contains also vray and standard materials scenes and rendering settings that created the images shown above.

Do you have the spare parts to do the repair? Some parts are missing! Recommended repair kit. Required spare parts. See product Add to cart. Required tools. Standard tool kit. Guide format : Pdf Integrate. See in HD. To do so, press the power button for a few seconds and wait for it to completely turn off.

Step 2 Flip over your PSP Step 3 Then grab the battery cover and remove it gently. Step 4 With a nylon spudger, gently pry on the battery. Step 5 Grab the battery and remove it. Step 6 With a cruciform screwdriver, remove the screw circled in red. Step 7 The next step of this guide requires that you remove the guarantee sticker of your PSP Step 8 Use the cruciform screwdriver and remove the screw circled in red.

Step 9 then remove the two cruciform screws circled in red on the picture. Step 10 Still using the cruciform screwdriver, remove the screw from the bottom edge of the PSP Step 11 Flip it over again so that the UMG reader cover is facing you. Remove the 2 cruciform screws located on the right of the back cover of your PSP Step 12 Flip it over again so that the screen is facing you.

Step 13 With a cruciform screwdriver, remove the screw circled in red. Note : Don't remove the home bar just yet, it is still attached to the console by two cables. Step 15 Pry on the LCD screen very carefuly. Note 1 : Be very cautious in order not to damage the screen! Step 16 Keep lifting very slowly the LCD screen to tip it over. Step 18 With the nylon spudger, gently pry to unlock the FPC connector from the microphone.

Then, remove the single screw from the bottom edge of the PSP which is positioned next to the barcode. Slide the spudger in between the outer casing of the PSP, beginning at the "R" shoulder button, and gently pry off the casing. Push the homebar to the right to release the tab located on the right side of the LCD screen. Again, the LCD screen is attached by ribbon cables, so do not remove it completely.

Flip the small brown locks on the four ribbon cable connectors up using a spudger or fingernail. Upon reassembly, make note that the stamped lettering faces down, and the large tab fits just above the motherboard to the right hand side of the left trigger. Being careful not to break the ribbon cable, use the spudger to peel the adhesive button of the the 'L' trigger off the PSP. Using a fingernail or spudger, flip up the retaining bracket on the d-pad and 'L' trigger ribbon cable.

Lift the black plastic bracket along with the d-pad contact pad, disconnecting the ribbon cable as you lift.

Remove the cable from the connector and remove the entire black piece from the PSP. Carefully bend back the black tab holding the power jack in place and start pulling the jack up to release it from this clip.

Push the black tab at the bottom of the speaker to pop the speaker out of place, and remove the speaker. The speaker is spring loaded, so be sure to keep an eye on it in case it starts doing flips into the air when you push the tab.

Be careful not to lose or damage it! Remove the cable carefully by lifting upwards from port attached to the motherboard. Flip up the lock and remove the ribbon cable located at the bottom edge of the PSP. Use a Phillips 00 screwdriver to remove the bottom left screw attached to the PSP. Open the UMD disk drive and locate the two small black rubber squares wedged in the space between the casing and the metal drive hinge on either side.

Detach the metal piece from where it is attached to the body underneath the rubber pieces that were just removed. The side of the piece that is closest to the door opening should now be loose. The whole piece should now be slid farther into the drive through the slots. Once you slide the piece toward the back of the slots, the side that is still attached can be pried towards the center of the drive on each side to remove it from the slots on the door. Pull up and the the left side carefully to remove the lid from the PSP.

The casing may have to flex a little bit to allow this.